求教，mach3 2.63电机运行圈数问题，本应跑1圈，实际跑25.X圈

青岛海子

我的驱动器设置4细分，mach3电机设置steps per 160（丝杠螺距按照5mm来设置） 速度 5000 加速度 50，正常z轴跑5mm电机应该转1圈，为何我的电机要转25圈还多，单位设置毫米，不解，请高人指点，不胜感激

[ 本帖最后由 青岛海子 于 2012-8-10 11:05 编辑 ]

青岛海子

最开始使用mach2.48时，artcam出的刀路跑正常，而ug出的刀路也是同样问题，5mm跑25圈还多，而且ug7.0出的刀路还报错，很多都不运行

skywang168

单位设成英寸了？

青岛海子

没有 是mm
%
N0010 G40 G17 G90 G70
N0020 G91 G28 Z0.0
N0030 T01 M06
N0040 G1 G90 X-.2136 Y-.1502 Z.3937 F196.9 S12000 D00 M03 M08
N0050 Z.1969
N0060 G3 X.0047 Y.0081 Z.0394 I.1445 J.0305 K.0396 F98.4
N0070 I-.0047 J-.0081 F137.8
N0080 G1 X.1324 Y.2293
N0090 G3 I-.1324 J-.2293
N0100 G1 X.2601 Y.4505
这个是UG出的刀路，不知道为什么mach在如N0060这样的就报错，在ug上面可以仿真运行的

[ 本帖最后由 青岛海子 于 2012-8-10 12:20 编辑 ]

wupingee

25.4是英寸吧？

青岛海子

继续上图，不解

[ 本帖最后由 青岛海子 于 2012-8-10 13:21 编辑 ]

青岛海子

%
N0010 G40 G17 G90 G70
N0020 G91 G28 Z0.0
N0030 T03 M06
N0040 G0 G90 X2.0354 Y-.8059 S2500 M03
N0050 G43 Z.1969 H00
N0060 Z-.5748
N0070 G1 Z-.5827 F86.6 M08
N0080 Z-.622 F23.6
N0090 X1.9567 Y-.9101
N0100 G2 X1.4043 Y-1.563 I-6.1585 J4.6509
N0110 G1 X1.378
N0120 X1.0744
N0130 G3 X1.9567 Y-.5067 I-5.2762 J5.3038
N0140 G1 Y-.0753
N0150 G2 X.8411 Y-1.461 I-6.1585 J3.8161
N0160 X.7745 Y-1.5247 I-5.0298 J5.188
N0170 X.7337 Y-1.563 I-4.9763 J5.2655
N0180 G1 X.3445
N0190 X.3723 Y-1.5523
N0200 X.4425 Y-1.5064
N0210 X.4787 Y-1.4761
N0220 G3 X.6123 Y-1.353 I-4.6805 J5.2169
N0230 X.6767 Y-1.2914 I-4.801 J5.08
N0240 X1.8612 Y.2248 I-4.8785 J5.0322
N0250 X1.9567 Y.508 I-.6498 J.3768
N0260 G1 X2.0354 Y.9738 F129.9
N0270 Z-.5827
N0280 G0 Z.1969
N0290 X-2.0354 Y.8297
N0300 Z-.5748
N0310 G1 Z-.5827 F86.6
N0320 Z-.622 F23.6
N0330 X-1.9567 Y1.228
N0340 G2 X-1.9255 Y1.369 I3.1681 J-.6264
N0350 G1 X-1.92 Y1.3916
N0360 X-1.9064 Y1.4388
N0370 X-1.8698 Y1.55
N0380 X-1.863 Y1.563
N0390 X-1.5967
N0400 X-1.6514 Y1.4579
N0410 X-1.6806 Y1.369
N0420 X-1.6917 Y1.3308
N0430 X-1.6961 Y1.3129
N0440 G3 X-1.7689 Y.8793 I2.9075 J-.7113
N0450 G1 X-1.7747 Y.8772
N0460 X-1.8665 Y.8205
N0470 X-1.9292 Y.7762
N0480 G2 X-1.9567 Y.7554 I-2.2726 J2.9646
N0490 G1 Y.4542
N0500 G2 X-1.8794 Y.5189 I.4803 J-.4943
N0510 G3 X-1.7855 Y.5888 I-2.3224 J3.2219
N0520 G1 X-1.7693 Y.6012
N0530 X-1.74 Y.621
N0540 X-1.6708 Y.6637
N0550 X-1.5434 Y.7106
N0560 G2 X-1.4666 Y1.2567 I2.7548 J-.109
N0570 G1 X-1.4634 Y1.27
N0580 X-1.4549 Y1.2993
N0590 X-1.433 Y1.3659
N0600 X-1.3567 Y1.5126
N0610 X-1.3101 Y1.563
N0620 X-1.2373 Y1.6417 F129.9
N0630 Z-.5827
N0640 G0 Z.1969
N0650 X-2.0354 Y-1.5016
N0660 Z-.5748
N0670 G1 Z-.5827 F86.6
N0680 Z-.622 F23.6
N0690 X-1.9567 Y-1.5494
N0700 G3 X-1.9336 Y-1.563 I.4803 J.791
N0710 G1 X-1.7949 Y-1.6417 F129.9
N0720 Z-.5827
N0730 Z-.5748 F110.2
N0740 X-.3961
N0750 Z-.5827 F86.6
N0760 Z-.622 F23.6
N0770 X-.496 Y-1.563
N0780 G2 X-.6768 Y-1.4073 I1.7071 J2.1649
N0790 X-1.5019 Y-1.4471 I-.6456 J4.8109
N0800 X-1.9567 Y-1.2527 I.0255 J.6887
N0810 G1 X-2.0354 Y-1.1762 F129.9
N0820 Z-.5827
N0830 G0 Z.1969
N0840 X-.2606 Y1.6417
N0850 Z-.5748
N0860 G1 Z-.5827 F86.6
N0870 Z-.622 F23.6
N0880 X-.1459 Y1.563
N0890 G3 X.777 Y1.4885 I.5263 J.7665
N0900 G1 X.7923 Y1.4957
N0910 G2 X.9862 Y1.563 I.4191 J-.8941
N0920 G1 X1.3224 Y1.6417 F129.9
N0930 Z-.5827
N0940 Z-.5748 F110.2
N0950 X1.1003
N0960 Z-.5827 F86.6
N0970 Z-.622 F23.6
N0980 X1.4365 Y1.563
N0990 G2 X1.9567 Y1.2492 I-.2251 J-.9614
N1000 G1 Y.6952
N1010 G3 X.8926 Y1.2818 I-.7453 J-.0936
N1020 G1 X.8777 Y1.2748
N1030 G2 X-.2822 Y1.37 I-.4973 J1.0547
N1040 G1 X-.3353 Y1.4089
N1050 G2 X-.397 Y1.4604 I.7157 J.9206
N1060 G1 X-.4282 Y1.4878
N1070 X-.5292 Y1.551
N1080 X-.5714 Y1.563
N1090 X-.8488 Y1.6417 F129.9
N1100 Z-.5827
N1110 Z-.5748 F110.2
N1120 X-.6355
N1130 Z-.5827 F86.6
N1140 Z-.622 F23.6
N1150 X-.9068 Y1.563
N1160 X-.9501 Y1.5504
N1170 X-1.0684 Y1.4764
N1180 X-1.1617 Y1.3755
N1190 X-1.2146 Y1.2738
N1200 X-1.2372 Y1.2006
N1210 G3 X-1.3088 Y.5467 I2.4486 J-.599
N1220 G1 X-1.3087 Y.5453
N1230 Y.5439
N1240 G2 X-1.3443 Y.4964 I-.0473 J-.0016
N1250 G1 X-1.4032 Y.4936
N1260 X-1.4724 Y.485
N1270 X-1.5669 Y.4502
N1280 X-1.6118 Y.4225
N1290 X-1.6313 Y.4094
N1300 X-1.6418 Y.4013
N1310 G2 X-1.7413 Y.3273 I-2.56 J3.3395
N1320 G3 X-1.9294 Y-.0401 I.2649 J-.3674
N1330 G1 Y-.7584
N1340 G3 X-1.4932 Y-1.211 I.453 J0.0
N1350 X-.6246 Y-1.1611 I.1708 J4.6146
N1360 G1 X-.6234 Y-1.161
N1370 X-.6222 Y-1.1608
N1380 G2 X-.5758 Y-1.1761 I.0085 J-.0522
N1390 G1 X-.5749 Y-1.177
N1400 X-.574 Y-1.1779
N1410 G3 X-.138 Y-1.5275 I1.7851 J1.7798
N1420 G1 X-.1118 Y-1.544
N1430 X-.0696 Y-1.563
N1440 X.0965 Y-1.465
N1450 G3 X.0272 Y-1.3475 I-.1177 J.0097
N1460 G1 X.0003 Y-1.3355
N1470 X-.0115 Y-1.3279
N1480 G2 X-.4067 Y-1.0111 I1.2226 J1.9298
N1490 G3 X-.6603 Y-.9276 I-.207 J-.2019
N1500 G2 X-1.4845 Y-.975 I-.6621 J4.3312
N1510 X-1.6932 Y-.7584 I.0081 J.2166
N1520 G1 Y-.0401
N1530 G2 X-1.6032 Y.1357 I.2168 J0.0
N1540 G3 X-1.4981 Y.2138 I-2.5986 J3.6051
N1550 G1 X-1.463 Y.2367
N1560 X-1.4164 Y.2539
N1570 X-1.3704 Y.2584
N1580 G2 X-1.3582 Y.2587 I.0904 J-4.3806
N1590 G1 X-1.3154 Y.2617
N1600 G3 X-1.0726 Y.5518 I-.0406 J.2806
N1610 G2 X-1.0077 Y1.1445 I2.284 J.0498
N1620 G1 X-.9962 Y1.1818
N1630 X-.9668 Y1.2384
N1640 X-.9164 Y1.2929
N1650 X-.8527 Y1.3327
N1660 X-.7789 Y1.3541
N1670 X-.701 Y1.3542
N1680 X-.626 Y1.333
N1690 X-.5697 Y1.2977
N1700 X-.5545 Y1.2843
N1710 G3 X-.4792 Y1.2216 I.9349 J1.0452
N1720 G1 X-.4172 Y1.1762
N1730 G3 X.9785 Y1.0611 I.7976 J1.1533
N1740 G2 X.9928 Y1.0679 I2.8883 J-6.1257
N1750 X1.6568 Y.3433 I.2186 J-.4663
N1760 X.5122 Y-1.1218 I-5.8586 J3.3975
N1770 X.45 Y-1.1813 I-4.7009 J4.8488
N1780 X.3209 Y-1.3002 I-4.6518 J4.9221
N1790 G1 X.3025 Y-1.3157
N1800 X.264 Y-1.3409
N1810 X.2044 Y-1.3639
N1820 X.1358 Y-1.3726
N1830 X.0596 Y-1.3621
N1840 X.0272 Y-1.3475
N1850 G3 X-.1067 Y-1.3737 I-.0484 J-.1078 F129.9
N1860 G1 Z-.5827
N1870 G0 Z.1969
N1880 X2.0354 Y-.8059
N1890 Z-.5827
N1900 G1 Z-.5906 F86.6
N1910 Z-.6299 F23.6
N1920 X1.9567 Y-.9101
N1930 G2 X1.4043 Y-1.563 I-6.1585 J4.6509
N1940 G1 X1.378
N1950 X1.0744
N1960 G3 X1.9567 Y-.5067 I-5.2762 J5.3038
N1970 G1 Y-.0753
N1980 G2 X.8411 Y-1.461 I-6.1585 J3.8161
N1990 X.7745 Y-1.5247 I-5.0298 J5.188
N2000 X.7337 Y-1.563 I-4.9763 J5.2655
N2010 G1 X.3448
N2020 X.3775 Y-1.5505
N2030 X.4588 Y-1.4939
N2040 X.4787 Y-1.4761
N2050 G3 X.6123 Y-1.353 I-4.6805 J5.2169
N2060 X.6767 Y-1.2914 I-4.801 J5.08
N2070 X1.8612 Y.2248 I-4.8785 J5.0322
N2080 X1.9567 Y.508 I-.6498 J.3768
N2090 G1 X2.0354 Y.9738 F129.9
N2100 Z-.5906
N2110 G0 Z.1969
N2120 X-2.0354 Y.8297
N2130 Z-.5827
N2140 G1 Z-.5906 F86.6
N2150 Z-.6299 F23.6
N2160 X-1.9567 Y1.228
N2170 G2 X-1.9255 Y1.369 I3.1681 J-.6264
N2180 G1 X-1.92 Y1.3916
N2190 X-1.9064 Y1.4388
N2200 X-1.8697 Y1.55
N2210 X-1.863 Y1.563
N2220 X-1.5967
N2230 X-1.6514 Y1.4579
N2240 X-1.6806 Y1.369
N2250 X-1.6917 Y1.3308
N2260 X-1.6961 Y1.3129
N2270 G3 X-1.7689 Y.8793 I2.9075 J-.7113
N2280 G1 X-1.7747 Y.8772
N2290 X-1.8665 Y.8205
N2300 X-1.9292 Y.7762
N2310 G2 X-1.9567 Y.7554 I-2.2726 J2.9646
N2320 G1 Y.4542
N2330 G2 X-1.8794 Y.5189 I.4803 J-.4943
N2340 G3 X-1.7855 Y.5888 I-2.3224 J3.2219
N2350 G1 X-1.7693 Y.6012
N2360 X-1.74 Y.621
N2370 X-1.6708 Y.6637
N2380 X-1.5434 Y.7106
N2390 G2 X-1.4666 Y1.2567 I2.7548 J-.109
N2400 G1 X-1.4634 Y1.27
N2410 X-1.4549 Y1.2993
N2420 X-1.433 Y1.3659
N2430 X-1.3566 Y1.5127
N2440 X-1.3101 Y1.563
N2450 X-1.2373 Y1.6417 F129.9
N2460 Z-.5906
N2470 G0 Z.1969
N2480 X-2.0354 Y-1.5016
N2490 Z-.5827
N2500 G1 Z-.5906 F86.6
N2510 Z-.6299 F23.6
N2520 X-1.9567 Y-1.5494
N2530 G3 X-1.9336 Y-1.563 I.4803 J.791
N2540 G1 X-1.7949 Y-1.6417 F129.9
N2550 Z-.5906
N2560 Z-.5827 F110.2
N2570 X-.3961
N2580 Z-.5906 F86.6
N2590 Z-.6299 F23.6
N2600 X-.496 Y-1.563
N2610 G2 X-.6768 Y-1.4073 I1.7071 J2.1649
N2620 X-1.502 Y-1.4471 I-.6456 J4.8109
N2630 X-1.9567 Y-1.2527 I.0256 J.6887
N2640 G1 X-2.0354 Y-1.1762 F129.9
N2650 Z-.5906
N2660 G0 Z.1969
N2670 X-.2606 Y1.6417
N2680 Z-.5827
N2690 G1 Z-.5906 F86.6
N2700 Z-.6299 F23.6
N2710 X-.1459 Y1.563
N2720 G3 X.777 Y1.4885 I.5263 J.7665
N2730 G1 X.7923 Y1.4957
N2740 G2 X.9862 Y1.563 I.4191 J-.8941
N2750 G1 X1.3224 Y1.6417 F129.9
N2760 Z-.5906
N2770 Z-.5827 F110.2
N2780 X1.1003
N2790 Z-.5906 F86.6
N2800 Z-.6299 F23.6
N2810 X1.4365 Y1.563
N2820 G2 X1.9567 Y1.2492 I-.2251 J-.9614
N2830 G1 Y.6952
N2840 G3 X.8926 Y1.2818 I-.7453 J-.0936
N2850 G1 X.8777 Y1.2748
N2860 G2 X-.2822 Y1.37 I-.4973 J1.0547
N2870 G1 X-.3353 Y1.4089
N2880 G2 X-.397 Y1.4604 I.7157 J.9206
N2890 G1 X-.428 Y1.4876
N2900 X-.5288 Y1.5509
N2910 X-.5714 Y1.563
N2920 X-.8481 Y1.6417 F129.9
N2930 Z-.5906
N2940 Z-.5827 F110.2
N2950 X-.6351
N2960 Z-.5906 F86.6
N2970 Z-.6299 F23.6
N2980 X-.9068 Y1.563
N2990 X-.9499 Y1.5505
N3000 X-1.0684 Y1.4765
N3010 X-1.1617 Y1.3755
N3020 X-1.2146 Y1.2738
N3030 X-1.2372 Y1.2006
N3040 G3 X-1.3088 Y.5467 I2.4486 J-.599
N3050 G1 X-1.3087 Y.5453
N3060 Y.5439
N3070 G2 X-1.3443 Y.4964 I-.0473 J-.0016
N3080 G1 X-1.4032 Y.4936
N3090 X-1.4724 Y.485
N3100 X-1.5669 Y.4502
N3110 X-1.6118 Y.4225
N3120 X-1.6313 Y.4094
N3130 X-1.6418 Y.4013
N3140 G2 X-1.7413 Y.3273 I-2.56 J3.3395
N3150 G3 X-1.9294 Y-.0401 I.2649 J-.3674
N3160 G1 Y-.7584
N3170 G3 X-1.4932 Y-1.211 I.453 J0.0
N3180 X-.6246 Y-1.1611 I.1708 J4.6146
N3190 G1 X-.6234 Y-1.161
N3200 X-.6222 Y-1.1608
N3210 G2 X-.5758 Y-1.1761 I.0085 J-.0522
N3220 G1 X-.5749 Y-1.177
N3230 X-.574 Y-1.1779
N3240 G3 X-.139 Y-1.5268 I1.7851 J1.7798
N3250 G1 X-.1149 Y-1.5421
N3260 X-.0698 Y-1.563
N3270 X.0974 Y-1.4668
N3280 G3 X.0294 Y-1.3486 I-.1176 J.011
N3290 G1 X-.0015 Y-1.3343
N3300 X-.0125 Y-1.3273
N3310 G2 X-.4067 Y-1.0111 I1.2236 J1.9292
N3320 G3 X-.6603 Y-.9276 I-.207 J-.2019
N3330 G2 X-1.4845 Y-.975 I-.6621 J4.3312
N3340 X-1.6932 Y-.7584 I.0081 J.2166
N3350 G1 Y-.0401
N3360 G2 X-1.6032 Y.1357 I.2168 J0.0
N3370 G3 X-1.4981 Y.2138 I-2.5986 J3.6051
N3380 G1 X-1.463 Y.2367
N3390 X-1.4164 Y.2539
N3400 X-1.3704 Y.2584
N3410 G2 X-1.3582 Y.2587 I.0904 J-4.3806
N3420 G1 X-1.3154 Y.2617
N3430 G3 X-1.0726 Y.5518 I-.0406 J.2806
N3440 G2 X-1.0077 Y1.1445 I2.284 J.0498
N3450 G1 X-.9962 Y1.1818
N3460 X-.9668 Y1.2384
N3470 X-.9164 Y1.2929
N3480 X-.8526 Y1.3328
N3490 X-.7788 Y1.3542

skywang168

我感觉你那就是英寸的，mach设置里看看单位

aiqdb

用别的后处理再试试。

鹤舞白沙

我也碰到这样的问题。不知道LZ解决了没有。

半桶水

单位设英寸了，后处理不用I、J、K，用R就好。

gbjs

速度设5000有可能吗？加速度设小了。我说的这些与你问的问题无关。

青岛海子

鹤舞白沙 发表于 2012-9-12 21:18
我也碰到这样的问题。不知道LZ解决了没有。

没有解决，UG里面单位设置为公制，后处理代码也是没有带单位的，可就是不知为什么会跑25.4圈，我为了正常运行，是将mach里面的单位选为英寸，这样运行走5mm电机刚好转1圈，目前还是停在桌面上运行，还没有装机使用，

鹤舞白沙

青岛海子 发表于 2012-9-17 23:21
没有解决，UG里面单位设置为公制，后处理代码也是没有带单位的，可就是不知为什么会跑25.4圈，我为了正常 ...

我是装机运行了，问题出在系统设置和软件的稳定性上了。

青岛海子

我这个没装机都不正常，上机更不可能正常了，感觉像是UG出的刀路单位上面有问题，另外mach不支持UG的螺旋下刀，之前报错的问题改成斜插下刀就没有了